Wick & Weigh

Wicks & fixes · October 24, 2026

How long to cure a candle: what each supplier actually says

7 minute read

A candle maker checking plain jar candles curing on wooden shelves, each with a dated sticky note

A candle can look finished an hour after you pour it. The top is set, the glass is cool, and it is hard to resist lighting it. But nearly every wax supplier tells you to wait, and they don’t agree on how long. This guide puts their numbers side by side and explains what you are waiting for.

Hardening is not curing

There are two different things happening after a pour.

Hardening is the wax going from liquid to solid. Nature’s Garden puts it at typically 24 to 48 hours, and that is roughly when a candle can be moved, labeled and packed without marking the surface.

Curing is slower. Suppliers describe it as the time the wax needs to settle and hold the fragrance oil evenly, which affects how strongly the candle smells when cold (cold throw) and when burning (hot throw). Nature’s Garden puts it bluntly: a candle may look solid within 24 to 48 hours, but that does not mean it is fully cured.

What suppliers publish

Source Soy Paraffin Coconut and blends Notes
Nature’s Garden 7 to 14 days 3 to 5 days Varies, check your wax supplier Hardening 24 to 48 hours is not the same as curing
Lone Star Candle Supply About a week before the first burn About a week (one figure for all waxes) Not given separately Calls skipping the cure the most common reason a candle smells weak
CandleScience (burn test guide) At least 24 hours before a burn test At least 24 hours At least 24 hours A minimum for testing how the candle burns, not a scent cure

Read across a row and the pattern is clear: soy is the wax that most needs time, paraffin needs less, and blends depend on the blend. Read down a column and you’ll see the figures aren’t measuring the same thing. CandleScience’s 24 hours is the minimum before you test the burn. Nature’s Garden’s and Lone Star’s figures are about scent.

Which number should you use?

It depends on what you are about to do.

  • Testing the burn (melt pool, flame, soot): the minimum before a burn test is short. CandleScience asks for at least 24 hours. Melt pool and flame behavior depend mostly on wick and wax, not on how settled the scent is. The wick test planner sets up that test.
  • Judging scent throw: use the longer figure for your wax. For soy, that means a week or two. Judging hot throw on a three-day-old soy candle is the most common way to blame a good oil or a good load.
  • Selling: use whatever cure you tested with. If your tests were judged at 10 days, ship candles that have had 10 days. Count the days the candle sits in your stock, not the day it reaches the customer, so the number stays under your control.

The most important rule is the one in every comparison: use the same cure time for every test you plan to compare. If one test sat for three days and the other for twelve, any difference in scent may just be the cure. Our guide to comparing two wick tests has a full list of what to keep the same.

A worked example: one batch, two questions

Say you are testing Golden Brands 464 soy in an 8 fl oz tumbler that is 3 inches across, and you want to answer two questions from one pour: which wick burns well, and how long this recipe needs before the scent is where you want it. Those are different questions with different waiting times, so the trick is to pour enough jars to answer both without guessing.

Step 1: the wick. In the wick test planner, a 3.0 inch jar in GB 464 lands in the 2.95 to 3.29 inch row of the CandleScience wick guide, which gives a CD 18 as the starting wick. The planner builds the usual three-candle test around it: CD 16, CD 18 and CD 20. That is three jars.

Step 2: the scent. For the cure question, pour three more jars with the starting wick (CD 18), so the only thing that changes between them is how long they rest. You will light one at day 3, one at day 7 and one at day 14. Those days come straight from the supplier figures above: 3 days is the low end Nature’s Garden gives for paraffin, 7 days is Lone Star’s “about a week” and the start of the soy range, and 14 days is the top of the soy range.

Step 3: the wax. Six jars in total. In the candle wax calculator, an 8 fl oz jar filled to 90% holds about 183 g of finished candle (236.6 ml brim full, 212.9 ml at the fill line, times the usual 0.86 wax factor). At an 8% fragrance load, measured as a percent of the wax weight, that splits into about 169.6 g of wax and 13.6 g of oil per jar. For six jars:

  • Finished candle: about 1,099 g (38.8 oz)
  • Wax: about 1,017 g (35.9 oz, a little over 2.2 lb)
  • Fragrance oil: about 81 g (2.9 oz)

8% sits inside every published limit for GB 464 on our wax specs page (Lone Star’s 7 to 9% is the tightest), so the load itself is not the variable you are testing. If you are pouring this as one pitcher, add a little extra wax for what stays on the pot and pitcher; the pour day planner adds that for you.

Step 4: the calendar. If you pour on a Saturday:

  • Sunday (day 1): the 24-hour minimum from CandleScience has passed, so you can start burn testing the CD 16, CD 18 and CD 20 jars for melt pool, flame height and soot. Don’t score scent from these; they are too young to be fair.
  • Tuesday (day 3): light the first cure jar and note cold throw before lighting and hot throw after the melt pool forms.
  • The next Saturday (day 7): the second cure jar, same room, same burn time, same notes.
  • Saturday two weeks out (day 14): the third cure jar.

When you read your notes, you are looking for the shortest cure where the throw stops improving. If day 7 and day 14 smell about the same to you, 7 days is your cure for this recipe. If day 14 is clearly stronger, use 14, and expect to plan stock two weeks ahead. If the wick test picked a different wick than CD 18, run the cure jars again with that wick before you settle, because a bigger or smaller melt pool changes hot throw on its own.

This is one batch, six jars and a little over two pounds of wax. That is a small price for a number you can repeat on every batch afterward.

Where to cure

Nature’s Garden recommends a cool, dry place out of direct sunlight, with air around each candle. It advises against airtight containers or wrapping during the cure, because trapped moisture can affect scent or the surface. Steady temperatures help too: Nature’s Garden links temperature swings to surface issues like frosting and sweating.

If you put lids on straight away for storage space, write it down. It’s one more thing to keep the same between tests.

Does longer always mean better?

Not without limit. The supplier ranges stop at about two weeks for soy, and nobody here publishes a figure past that. Past the recommended window, a longer cure isn’t a fix for a load that’s too low, a wick that’s too small, or oil added below the temperature your supplier gives. Lone Star’s own list of weak-throw causes puts curing next to fragrance temperature, stirring time and wick size, and suggests checking all of them. If a candle still smells faint after a full cure, look at those before you blame the oil. The candle troubleshooter covers weak scent cause by cause, and the wax specs page lists the add-oil temperatures each supplier publishes.

Write the pour date on the base

A small sticker with the pour date and the recipe code on every test candle and every batch makes cure times easy to follow, and makes "is this one ready?" a glance instead of a guess.

Honest limits

The cure times above are what these suppliers publish. They are general guidance. Your wax, oil and room will decide what works, so test scent at more than one cure time (for example 3, 7 and 14 days) from the same batch and use the shortest one that gives you the throw you want.

Sources

Work it out for your own candles

Wick Test PlannerCandle Wax Specs Compared

Photo credits: Roman Mesyancev · Abigail Ybarra · Jessica Mangano · Mustafi Numann · Allison Saeng · User_Pascal · Maria Kovalets on Unsplash