Wick & Weigh

Wax & fragrance · November 7, 2026

How much fragrance oil per pound of wax? A 6 to 12% chart

3 minute read

A digital scale reading in grams with a white bowl on top, on a wooden table

For one pound of wax (16 oz by weight), fragrance oil at 6% is 0.96 oz, at 8% it is 1.28 oz, at 10% it is 1.6 oz, and at 12% it is 1.92 oz. That assumes the percentage is of the wax weight, which is how US wax suppliers write it. Weigh the oil on the same scale as the wax, in the same units.

The one-pound chart

Load (of wax weight) Oil per 1 lb wax, oz Oil per 1 lb wax, grams Wax plus oil, oz
6% 0.96 27.2 16.96
8% 1.28 36.3 17.28
10% 1.60 45.4 17.60
12% 1.92 54.4 17.92

The math is wax weight times the load as a decimal: 16 oz x 0.08 = 1.28 oz. The last column is what the melted mixture weighs before dye. It is not a fill weight for a jar, because the jar holds a volume and wax is lighter than water. For fill weights, use how much wax for an 8 oz jar.

Bigger batches

Scale the same numbers. Oil in ounces by weight:

Wax in the pot 6% 8% 10% 12%
1 lb 0.96 1.28 1.60 1.92
2 lb 1.92 2.56 3.20 3.84
5 lb 4.80 6.40 8.00 9.60
10 lb 9.60 12.80 16.00 19.20

Ten pounds at 10% is a full pound of oil, which is a quick way to see how much 10% really is. If you are pouring for a market table, the fragrance load calculator does this for any wax weight and also shows the amount in grams.

The chart is arithmetic, not a limit

Nothing in the chart tells you how much your wax can hold. CandleScience’s soy wax troubleshooting guide says most good fragrance oils are strong at 6 to 8% and that you should not use more than 10%, even if your wax says it can hold more. Its guide for AAK 464 soy wax says the wax has a maximum fragrance load of 10% but that using that much is not always ideal, and it suggests starting at 6%, roughly 1 oz per pound of wax.

So 12% is in the chart for comparison only. It is above the ceiling those suppliers give, and extra oil the wax cannot bind tends to show up as oil on the surface or a smokier burn, not a stronger scent. Check the page for your exact wax, since limits differ from one wax to the next. The wax specs chart lists what we have collected.

Worked example: a 2 lb test batch at 8%

Two pounds is 32 oz, and 32 x 0.08 = 2.56 oz of oil. Together with the wax that is 34.56 oz before dye. If your wax tops out at 7%, use 32 x 0.07 = 2.24 oz instead. The arithmetic stays the same and only the percentage you choose changes.

Weigh the oil rather than measuring it by volume. A fluid ounce measures space and an ounce on a scale measures weight, and fragrance oils do not weigh the same as water. Our guide on fluid ounces versus weight covers why the two get mixed up. If the percentage reads the other way in your recipe, as a share of the finished candle, see fragrance load, explained for the conversion.

Mistakes that skew the amount

The most common one is applying the percentage to the jar’s label size. A jar sold as 8 oz does not necessarily take 8 oz of wax, so weigh the wax first and base the oil on that number.

The next is treating a wax’s maximum as a target. A maximum is a ceiling, and most makers land lower. Start near the supplier’s suggested load, change one thing at a time, and keep notes on wax, oil, load and the date you poured. If a candle sweats, smokes or has a weak throw, look at the wick and cure time as well before adding more oil.

The last is leaving the denominator off the batch sheet. Write “8% of wax weight,” not just “8%,” so a repeat batch uses the same amount.

Where this stops: this is arithmetic and published supplier guidance, not a promise about how your candle will perform. Wax, oil, wick and process all interact, so test a finished candle before you scale up.

Photo credits: User_Pascal · Mustafi Numann · Allison Saeng · Maria Kovalets · Mary Skrynnikova · Roman Mesyancev · Julee Juu · Abigail Ybarra · Scott Precious on Unsplash