Wick & Weigh

Wax & fragrance · October 22, 2026

Pour day check: finished fill weight vs wax-only weight

9 minute read

A freshly poured candle in a small glass jar, its wick held straight by a pencil resting across the rim

A pour sheet for a mixed batch has two kinds of weight on it, and they look alike. One is the finished fill weight: everything that ends up in one jar, wax and fragrance oil together. The other is the wax-only weight: the part of that fill that came out of the wax bag. On a pour day with tumblers and tins in the same scent, it is easy to weigh to the wrong one. Nothing looks wrong at the time. The jars set, the tops look smooth, and the mistake only shows up later as a label that claims more than the jar holds, or a fill line that creeps up towards the rim.

This guide walks through one pour day from start to finish and shows what your scale should read at each stage. The aim is simple: know which number you are checking against before the wax is hot.

The two numbers, side by side

Most suppliers describe fragrance load as a percentage of the wax. Lone Star Candle Supply puts it plainly on its fragrance calculator page: the load is a percentage of the wax weight, so you multiply the wax weight by the load as a decimal. At 8%, every 100 g of wax gets 8 g of oil, and the jar ends up holding 108 g.

That means the fill weight and the wax weight can never be the same number. The fill is always the larger one. With a load of 8% of wax:

  • wax-only weight = fill weight ÷ 1.08
  • oil weight = fill weight − wax-only weight

The strongest starting point is a known or tested fill weight, meaning the combined wax and fragrance weight you want in one candle. Our candle wax calculator works the same way: give it a fill weight, or a jar size to estimate one from, and it splits the fill into wax and oil.

A worked pour day

Here is the batch we will follow. All numbers come straight from our pour day planner.

  • 12 tumblers sold as 8 oz, each filled with 6.5 oz of finished candle
  • 6 tins sold as 4 oz, each filled with 3.4 oz
  • Fragrance load 8% of wax, one scent for the whole batch
  • 5% extra for the pitcher, thermometer and spout
  • A pitcher that holds 4 lb of wax at a time

Why 6.5 oz in a jar sold as 8 oz? The “8 oz” on a jar listing is usually fluid ounces of volume to the brim. Wax is lighter than water and you stop below the rim, so the finished candle weighs less. Our guide to why an 8 oz jar holds about 6.4 oz of candle covers that in full. For this guide, take 6.5 oz as a fill weight that was measured from a past batch.

The planner splits each vessel like this:

Vessel Finished fill (wax + oil) Wax only Oil Scale reads after pouring one
8 oz tumbler 6.50 oz (184 g) 6.02 oz (171 g) 0.48 oz (14 g) 6.50 oz
4 oz tin 3.40 oz (96 g) 3.15 oz (89 g) 0.25 oz (7 g) 3.40 oz

Look at the last column. When you pour a jar on a tared scale, you are pouring fragrance-loaded wax, so the target is always the finished fill. The wax-only column is for the bag and the pitcher, never for the jar.

For the whole session, the planner gives:

  • Finished candle in all 18 vessels: 98.40 oz
  • With 5% extra: 103.32 oz in total
  • Wax to melt: 95.67 oz (2,712 g), about 6 lb
  • Oil to measure: 7.65 oz (217 g)
  • Pours: 2, because 95.67 oz of wax does not fit a 4 lb (64 oz) pitcher in one go
  • Each pour: 47.83 oz (1,356 g) of wax and 3.83 oz (108 g) of oil, 51.66 oz together

Now the checks.

Step 1: weigh the wax for one pour, not the whole day

Tare the empty pitcher and weigh 47.83 oz of wax flakes into it. That is the wax-only number for one pour. If you weighed the whole day’s 95.67 oz, it would overflow a 4 lb pitcher, and a half-melted overflow is how loads drift: you end up adding oil to a guess.

Weigh the second pour’s wax into a separate bag or bowl now, while you are at the scale. It is one less thing to do with hot wax on the stove.

Step 2: measure the oil for each pour into its own cup

Weigh 3.83 oz of oil into one cup and another 3.83 oz into a second cup. Label them “pour 1” and “pour 2”. If you pour all 7.65 oz into the first pitcher, the first nine or so candles get a double load and the rest get none.

Check the oil against your wax’s limit before it goes anywhere. Our fragrance load calculator and wax specs page list what each supplier publishes for its wax. Eight percent sits inside most published container soy limits, but your wax is the one that counts.

Step 3: check the pitcher after the oil goes in

Melt the wax, bring it to your supplier’s add-oil temperature, and stir in the oil. CandleScience’s soy candle walkthrough, for example, adds the fragrance once the wax reaches 185°F; your wax may differ.

Now put the pitcher back on a scale that you tared with the empty pitcher earlier. It should read close to the pour total: 47.83 + 3.83 = 51.66 oz. This is the first place the two numbers meet. If the scale shows about 47.8 oz, the oil never went in. If it shows well over 51.66 oz, something else did, perhaps a second dose of oil or wax left from an earlier batch.

A thin film on the thermometer and spoon will take a little off. That is what the 5% extra is for.

Tare against the empty pitcher, not the melted wax

Write the empty pitcher's weight on a strip of tape on its handle. Then you can check the pitcher at any moment during the day, whether or not you remembered to tare. Pitcher reading minus tape number equals what is inside.

Step 4: pour each jar to the finished fill

Set a tumbler on the scale, tare, and pour until it reads 6.50 oz. Not 6.02. The wax-only number is now inside the pitcher mixed with oil; you cannot pour wax-only into a jar.

Here is what each mix-up costs on this batch:

  • Pouring tumblers to 6.02 oz. Each jar is short by 0.48 oz, about 7% of the candle. Across 12 tumblers that is 5.8 oz of candle left in the pitcher, which looks like you over-melted when really every jar is light. If your label says 6.5 oz, every jar is under its label.
  • Treating 6.5 oz as the wax and adding oil on top. If you planned the day as 6.5 oz of wax per tumbler and added 8% oil, each jar would need 7.02 oz to take its full share. Either you pour the jars higher than your tested fill line, or you run out before the last jars and the oil in them no longer matches your plan.

The tins work the same way: tare, pour to 3.40 oz, not 3.15 oz.

Check every jar, not just the first. Jars from the same case can vary a little in thickness and height, so the same fill weight may sit at a slightly different height in each. Pouring by weight keeps every candle the same, which matters more than the line looking identical.

Step 5: check what is left after each pour

The first pour has 51.66 oz of loaded wax in it. Nine of the 18 vessels go in this pour if you split by count, but the jars do not split evenly by weight, so do it by the sheet. Suppose pour 1 fills all 6 tins and 4 tumblers:

  • 6 × 3.40 oz = 20.40 oz
  • 4 × 6.50 oz = 26.00 oz
  • Poured: 46.40 oz

That leaves 51.66 − 46.40 = 5.26 oz in the pitcher. The next tumbler needs 6.50 oz, so stop: this pour cannot fill another one. Leave the 5.26 oz for a test jar or a sample tin, or let it set in a small container to re-melt later in the same scent. It already carries the right load, so mixing it into pour 2 does no harm.

Pour 2 then has to fill the 8 tumblers that are left: 8 × 6.50 oz = 52.00 oz. That is just over the 51.66 oz in the second pitcher, so remelt the 5.26 oz you saved from pour 1 and add it. You now have 56.92 oz, enough for all 8 tumblers with about 4.92 oz to spare for drips and a test sample.

The number to watch is the remainder at the end of each pour. If it is far below what the sheet expects, your jars ran heavy. If it is far above, they ran light. Either way you find out today, while the batch can still be fixed, rather than at labeling.

Step 6: label from the fill you actually poured

The net weight on a candle label is the finished candle, wax plus oil, not counting the jar or lid. Our label net weight calculator turns 6.50 oz into Net Wt. 6.5 oz (184 g). If the jars had been poured to the wax-only 6.02 oz, the honest line would be Net Wt. 6 oz (170 g), a different label.

NIST Handbook 133 is the manual US weights and measures inspectors use to check the net contents of packaged goods, including the procedure for packages labeled by weight. You do not need to read it to pour candles, but it explains why the label number should come from a weighed jar and not from the plan.

For the other lines on the label, see our US candle label checklist.

What this check can and cannot tell you

It catches: missing oil, double oil, jars poured to the wrong number, and a pour sheet built on wax-only weights by mistake.

It does not catch: a wrong fill weight in the first place. If 6.5 oz is too much for your jar, every check above will pass and your candles will still be too full. Measure the fill from a real jar, or pour one test jar to your line and weigh it, before planning a full day.

Some honest limits:

  • The planner’s numbers come from simple arithmetic on the fill weights you enter. When we estimate a fill from a jar’s fluid ounces, we use a 0.86 planning factor that many supplier calculators share. Your wax and your fill line will move it.
  • A kitchen scale that reads to 0.1 oz or 1 g is fine for the jars. For small oil amounts, a scale that reads to 0.01 oz or 0.1 g is easier to trust.
  • Some fragrance flashes off from hot wax. That loss is usually small next to pouring a jar to the wrong number, but it means the pitcher check in Step 3 is a sanity check, not a precise test.
  • The method is arithmetic plus what suppliers publish, and your own test jars are the final word.

Sources

Work it out for your own candles

Pour Day PlannerCandle Wax Calculator

Photo credits: shri · Mustafi Numann · Allison Saeng · User_Pascal · Maria Kovalets · Roman Mesyancev · Mary Skrynnikova · Julee Juu · Abigail Ybarra on Unsplash